filter press

板框压滤机压不干原因
2023/07/22 679
板框压滤机压不干的原因可能包括：过滤速度过快，导致滤饼中含有过多的水分。淤泥固含率低，导致滤饼不容易变得干燥。操作不当，如没有充分挤压或排出水分。根据以上原因，可以尝试降低过滤速度或增加过滤...
View full text
板框压滤机压不紧是什么原因造成的
2023/07/22 568
板框压滤机压不紧的原因可能包括：油泵吸空或吸油管堵塞：检查油箱油位是否过低，检查吸油管是否堵塞，清理吸油管。滤板密封面有杂物：清理滤板密封面上的杂物。油泵损坏或磨损：更换或修理油泵。溢流阀工作...
View full text
板框压滤机不压也不送
2023/07/22 486
板框压滤机不压也不送的原因可能包括：电源故障：检查电源是否正常，确保电源连接牢固，电压稳定。溢流阀故障：检查溢流阀是否正常工作，确保其调压正常，密封良好。滤板问题：检查滤板是否破损或密封不严，...
View full text
板框压滤机常见故障及解决办法
2023/07/22 370
板框压滤机常见的故障及解决方法如下：压力不足：检查溢流阀、油位、油泵、阀块和接头处泄漏情况，更换或维修。保压不佳：更换活塞密封圈、油路泄漏、液控单向阀清洗或更换。滤板向上抬起：安装基础不平整、...
View full text
压滤机的故障和处理方法
2023/07/22 376
压滤机常见的故障和处理方法如下：滤板破裂：进料压力过大或进料速度过快导致滤板破裂。处理方法：调整进料压力，降低进料速度。液压系统有噪音：液压系统吸入空气或紧固件松动导致有噪音。处理方法：打开放气...
View full text
Filter press slurry spraying causes treatment
2023/07/22 840
The causes and treatment of slurry spraying from filter presses are as follows: Broken filter cloth: broken filter cloth will lead to filter press slurry spraying, and it is necessary to regularly check whether the filter cloth is worn, broken and other problems, and replace it in time. At the same time, you need to avoid using hard objects to bump the surface of the filter cloth in the process of use, so as not to break again. In order to solve this...
View full text
压滤机故障诊断与维修
2023/07/22 503
压滤机常见的故障和解决方法如下：滤板损坏。原因：滤板受压过大，或进料浓度过高。滤液不清。解决方法：更换新的滤布，清洗滤布，加强滤液冲洗。原因：进料不足或进料浓度过低，滤布破损或选择不当，压力不...
View full text
What happens when the filter press cloth breaks
2023/07/22 400
压滤机滤布破裂会产生以下影响：压滤机的内压和反吹气会产生波动，滤布破损越严重波动越大。会有大量的产品从破损处流失，造成产品产量与进料量不匹配，即产品产量明显少于正常出料量。从压滤机视镜可以观察...
View full text
压滤机滤饼不均匀
2023/07/22 385
压滤机滤饼不均匀的原因可能有以下几种：进料不足或太稀：进料不足或太稀会导致滤饼形成不均匀。滤布损坏：滤布损坏会导致滤液泄漏，也会导致滤饼形成不均匀。为了解决这个问题，可以采取以下措施2：增加...
View full text
Analysis of the causes of high moisture in filter presses
2023/07/22 568
压滤机水分大的原因可能有以下几种：进泥浓度低：污泥浓度过低，会导致直接机械污泥脱水效果不理想，需增加污泥浓缩池。滤布老化：滤布使用时间过长，毛孔堵塞，导致过滤效果下降。滤带张力不足：上下滤带的...
View full text

Expand More

downloadingDownload

Product Classification

service

Service Support

Technical Literatureliterature

Filter Press Dewatering System for Lithium Mica Concentrate
2024/08/18 547
Lithium has a low melting point, high boiling point, the most negative potential, light weight and other characteristics, is widely used in new energy vehicles, nuclear industry, aviation, medical and other fields. Lithium is the most important basic raw material for the new energy industry, and is known as the "new energy of the 21st century". In order to accelerate the realisation of the strategic goal of "Carbon Neutral, Carbon Peak", China...
View full text
Plate and frame diaphragm chamber filter press operation process common problems and treatment
2024/07/29 560
In the coal gasification industry, the gasification filter cake is usually blended into the power coal for blending and use, but because of the high water content of the filter cake, direct blending will cause power coal plugging. In order to reduce the risk of power coal blending and plugging, it is necessary to further reduce the water content of the filter cake. Plate and frame filter press can reduce the water content of filter cake very well, so to ensure that the plate...
View full text
Optimisation of fast-opening high-pressure diaphragm filter press system in coal washing plant
2024/07/28 561
Filter press is the commonly used equipment for tailing coal treatment and dewatering in coal washing plant at this stage, which has the advantages of strong processing capacity, good dewatering effect, low noise, low energy consumption and so on. The fine coal slurry (particle size below 0.25mm) dewatering of Hupoji Coal Wash Plant uses ZKG450/2000-U type fast-opening diaphragm filter press, and the products are conveyed through the belt-type ...
View full text

View All

Contact UsAbout us